Spiral Binding Machine In Chennai
One of the most common styles of punch and bind machines are the plastic comb binding which is mostly known as the GBC Binding. It is comparatively an easy process and it is almost the same as that of all the manual comb binding machine. It is similar and it is easy to operate too. This machine has simple push button control rather than a lever which is the common site for all other machines. There are simple methods by which the binding process is done by the plastic comb binding.
Select the Correct Size of Comb Binding Spine
At first check the size guide to see the binding size which is required by you. This is necessary because the bind should be of the proper size hence it is important to check the size of the bind before starting off with the process. A comb biding which is too small will delay usability as well as the durability of the document as the pages are not going to turn freely and can ultimately rip off from the machine. On the other hand which are too large is going to look awkward. It is will not function properly. It will not be well fitted to the comb binding machine. The best way to judge the proper size of the comb binding to be used is the appearance of it and you can determine the exact size from the look too.
Pull or Push the Lever for Opening the Comb Binding Depending On the System
Most of the systems have only one lever which helps to operate the mechanism of punch by the machine by pulling forward the lever and it works as the comb binding opener by pulling it backwards. Electric punches along with some manual systems has separate comb binding lever which is generally pulled towards the operator to have the same utility for both the machines. Opening the comb binding at a long distance will cause the system to snap shut and also possibly fly off the whole system of the machine. It is important to open the binding to a level enough to fit all the pages into . Make sure that the opener is closed from all the ways while the pages are being inserted for binding.
Bookbinding is the process of physically assembling a book of codex format from an ordered stack of paper sheets that are folded together into sections or sometimes left as a stack of individual sheets. The stack is then bound together along one edge by either sewing with thread through the folds or by a layer of flexible adhesive. Alternative methods of binding that are cheaper but less permanent include loose-leaf rings, individual screw posts or binding posts, twin loop spine coils, plastic spiral coils, and plastic spine combs. For protection, the bound stack is either wrapped in a flexible cover or attached to stiff boards. Finally, an attractive cover is adhered to the boards, including identifying information and decoration. Book artists or specialists in book decoration can also greatly enhance a book’s content by creating book-like objects with artistic merit of exceptional quality.
1. For 3 to 1. First you’ll need to set the dial on the left, check the pins are in the correct position for the page dimension you are using, in this case 34 pushed in for A4.
2. Before you start any binding always test with a piece of scrap paper to ensure that the holes are centred along the length of the document.
3. You can adjust the position of the holes by moving the paper guide and margin lever.
4. Now that we’re ready to bind make sure pages are level and place the document into the machine ensuring it is tight against the paper guide.
5. When ready pull down the large handle on the right to punch the paper and put the pages face down on the desk.
6. We recommend punching no more than 25 sheets of 80gsm or 2 clear acetate covers in one go to avoid damaging the machine.
7. Once all pages have been punched for a neat finish move the back page to the front as this will hide the join inside your document once bound.
8. Make sure all holes line up and place document on the edge of the desk with a slight overhang.
9. Adjust the clamp to the size of the wire you are using.
10. Thread the wire through the holes just enough so that the C opening is facing towards you.
11. Pinch the bottom of the document just above the wire tightly to lock it in position and carefully place the document in the magnetic clamp, ensuring the wire is flat.
12. Pull the handle towards you slowly until the clamp grips the wire and then squeeze firmly.
13. Remove the document and ensure wire is clamped sufficiently; the clamp can be adjusted using the dial if required.
14. The join should be clearly visible but closing the back page will conceal this inside the document.
15. Your document is now ready.
If using plastic combs, again set the dial on the left, pull out all of the 3 to 1 pins and check the pins are in the correct position for the page dimension you are using, in this case 21 pushed in for A4.
16. You can adjust the position of the holes by moving the paper guide and margin lever.
17. Now that we’re ready to bind make sure pages are level and place the document into the machine ensuring it is tight against the paper guide.
18. When ready pull down the large handle on the right to punch the paper and put the pages face down on the desk.
19. We recommend punching no more than 25 sheets of 80gsm paper or 2 clear acetate covers in one go to avoid damaging the machine.
20. Once all sheets have been punched place the comb over the teeth of spreader.
21. Pull the handle on the left slowly, making sure the comb opens towards you.
22. Place the document face down onto the comb so that it doesn’t come apart in use.
23. Then push the handle forward gently to close.
24. Your document is now ready and can be removed.
25. Don’t forget when binding to empty the tray regularly as this will avoid the machine getting jammed.